Basics
Large format view cameras are usually tripod mounted and lend themselves
to a more contemplative style than the more portable 35mm and 2 1/4
formats. The Calumet 4x5 Standard model view camera is a lightweight,
portable tool that produces superior, fine grained images because of its
large format and ability to adjust for a minimum
of image distortion.
Setting Up and Focusing Image
Set the camera on the tripod, attach a cable release to the shutter
mechanism, level the camera and return all controls to their
zero-neutral (centered) position. Open the shutter for viewing by
cocking it and pressing the small, adjacent locking lever on the top,
outer rim of the lens. Open the aperture to allow maximum light through
the aperture for focusing.
Frame your subject at first by centering the image on the groundglass in
the rear of the camera. The glass has a grid inscribed on it which can
be used to aid positioning. The image will be reversed from top to
bottom as well as from side to side.
Use the control knobs to center the image - the back
of the camera will move from side to side and the front lens board will
move up and down or side to side. Before attempting to move any camera
part, be sure to loosen the associated thumb screw or clamp. After
making adjustments, tighten the thumb screw or clamp finger tight. See
the section later in this document entitled "How to Perform Camera
Movements" for information on which knobs control specific functions.
You will need to adjust the focus of your image as you compose. This is
done by sliding either the back of the camera or the lens board in front
until the image appears sharpest. To do this, loosen the front and back
locking screws, then adjust the focus with either the adjacent focusing
knobs or by lifting up the focusing knob release lever and sliding the
front or back of the camera along the rail.
If you move the back of the camera, the lens-subject relationship will
remain constant. If you move the front, lens to subject distance change
appreciably. Final focus is done by moving the back of the camera.
The reflective quality of the groundglass on the rear of the camera
sometimes makes it difficult to see your image to focus it. If needed,
fasten the black focusing cloth in its clips on the back of the camera
and drape it over your head and the back of the camera in a tent like
fashion. This will exclude most extraneous light, making the image
easier to see. While focusing use a loupe to make sure the image is
sharp.
The pebbled texture of the glass also makes it difficult to find the
sharpest focus. The point of sharpest focus is where the converging
light rays from the image come together. So it is sometimes easier to
focus for image brightness than for image sharpness.
A final point in focusing is to check the depth of field. This is done
by stopping down the aperture while looking at the image on the
groundglass. You will need to be under the focusing cloth while you're
stopping down the lens or it will be practically impossible to see the
differences in the depth of field.
As with any other lens, the overall depth of field of the view camera
lens will be controlled by the size of the aperture: the smaller it is,
the greater will be the depth of field. Select a point approximately
one-third of the way into the subject on which to focus. The resulting
area of sharpness will be twice as deep behind the point of focus as in
front of it.
Camera Movements - How They Affect the Image
The tilts, swings, slides, and rising and falling front of the 4x5 camera allow the photographerTilting the camera's back will elongate or correct distortion of the image horizontally; swinging the back
Tilting the front of the camera affects the focus because the focal plane of the lens moves. Swinging the front of the camera swivels the lens to the left or right and, as a result, skews the focal plane of the lens to one side or the other. The general
Slide, rise, and fall move the entire front or back of the camera on a flat plane. Slide moves the front or back to the left or right; rise moves the front straight upward; fall moves the front straight downward. These movements will allow the angle between the planes of film, lens, and subject to remain the same but will change the placement of the image on the film.
A slide of either the back or front of the camera produces similar results - image shape does not change with a back slide, but it changes slightly with a front slide. Rise or fall of the front causes a change in the point of view (or the space relationship) between any objects in the frame as well as a slight change in shape.
Film Loading
After you've made the final adjustments to your image composition, you're ready to load film into the camera. As mentioned earlier, Media LoanBefore loading film into the sheet
SHEET FILM LOADING
The film sheets must be loaded into the holder in complete darkness. Load the sheets with the emulsion side facing out. For positive identification of the emulsion side of the film while working in the dark, there are a series of notches in the corner of the sheet, When the film is held in the right hand with the thumb and index finger at the lower right hand corner, if the index finger is resting on the notches, the emulsion side is facing up.Use the left thumb and forefinger to help guide the edge of the film and push completely into place. Slip a fingernail under the end to try and lift it up. If it lifts up, the film hasn't actually slid into the grooves.
Finally, close the flap at the bottom of the holder and insert the dark slide with the lighter edge (silver
POLAROID FILM LOADING
To load film into the Polaroid holder follow theThe Polaroid holder must be clean to operate properly, but doesn't need cleaning with each use as do the film sheet
Before inserting the Polaroid film packets, check to make sure the operating lever moves the catch at the end of the holder which must grab the metal strip on the end of the film packet. Also, when removing the center of the film packet to expose the film, don't remove it all the way as it will then be impossible to reinsert. Finally, when you're ready to process the Polariod sheet, make sure the operating lever is pushed all the way to the P and not caught on an adjacent lever.
Exposing the Film
After you've taken a light meter-
-
-
-
- Bellows Length
- ------------------------ = Exposure Increase
- Focal Length
-
-
-
Close the camera shutter
After exposing your film, replace the dark slide with the dark edge out and turn the latches on the end of the holder to make certain the slide won't be accidentally pulled out.
No comments:
Post a Comment