Thursday, 26 June 2014

Evaluation

The photographers I researched are John Schott, Ansel Adams, Hamish Fulton, Richard Long, Edward Weston, Ed Ruscha, Lewis Baltz, John Davies, Nicholas Nixon, Eugene Atget, Alfred Stieglitz, Frank Gohlke, Henry Wessel, Robert Adams, Axel Hutte, Bernd and Hilla Becher, Stephen Shore, Andreas Gursky and Edward Butynsky. I took my photographs at Hartlepool Marina and Church Square, there was no difficulty with taking the photos and processing the images. I took my photographs round church square and near the church and University and near the Municipals building also looking right at the church.the photos I took are of the Marina looking out on to the boats and the church at Church Square.

5x4 Camera


Basics

 Large format view cameras are usually tripod mounted and lend themselves to a more contemplative style than the more portable 35mm and 2 1/4 formats. The Calumet 4x5 Standard model view camera is a lightweight, portable tool that produces superior, fine grained images because of its large format and ability to adjust for a minimum of image distortion.

 

Setting Up and Focusing Image

Set the camera on the tripod, attach a cable release to the shutter mechanism, level the camera and return all controls to their zero-neutral (centered) position. Open the shutter for viewing by cocking it and pressing the small, adjacent locking lever on the top, outer rim of the lens. Open the aperture to allow maximum light through the aperture for focusing.

Frame your subject at first by centering the image on the groundglass in the rear of the camera. The glass has a grid inscribed on it which can be used to aid positioning. The image will be reversed from top to bottom as well as from side to side.

Use the control knobs to center the image - the back of the camera will move from side to side and the front lens board will move up and down or side to side. Before attempting to move any camera part, be sure to loosen the associated thumb screw or clamp. After making adjustments, tighten the thumb screw or clamp finger tight. See the section later in this document entitled "How to Perform Camera Movements" for information on which knobs control specific functions.

You will need to adjust the focus of your image as you compose. This is done by sliding either the back of the camera or the lens board in front until the image appears sharpest. To do this, loosen the front and back locking screws, then adjust the focus with either the adjacent focusing knobs or by lifting up the focusing knob release lever and sliding the front or back of the camera along the rail.

If you move the back of the camera, the lens-subject relationship will remain constant. If you move the front, lens to subject distance change appreciably. Final focus is done by moving the back of the camera.

The reflective quality of the groundglass on the rear of the camera sometimes makes it difficult to see your image to focus it. If needed, fasten the black focusing cloth in its clips on the back of the camera and drape it over your head and the back of the camera in a tent like fashion. This will exclude most extraneous light, making the image easier to see. While focusing use a loupe to make sure the image is sharp.

The pebbled texture of the glass also makes it difficult to find the sharpest focus. The point of sharpest focus is where the converging light rays from the image come together. So it is sometimes easier to focus for image brightness than for image sharpness.

A final point in focusing is to check the depth of field. This is done by stopping down the aperture while looking at the image on the groundglass. You will need to be under the focusing cloth while you're stopping down the lens or it will be practically impossible to see the differences in the depth of field.

As with any other lens, the overall depth of field of the view camera lens will be controlled by the size of the aperture: the smaller it is, the greater will be the depth of field. Select a point approximately one-third of the way into the subject on which to focus. The resulting area of sharpness will be twice as deep behind the point of focus as in front of it.


 

Camera Movements - How They Affect the Image

The tilts, swings, slides, and rising and falling front of the 4x5 camera allow the photographer to correct converging or diverging lines in a composition or to deliberately distort an image. Tilt and swing refer to the movements of the front or back of the camera at an angle. Tilting moves the front or back around a horizontal axis. Swing is the movement around a vertical axis - it twists the front or back to the left or right.
Tilting the camera's back will elongate or correct distortion of the image horizontally; swinging the back will elongate or correct distortion of the image vertically and will also affect the focus. The farther the groundglass is from the lens, the larger the image will be. The part of the groundglass that moves away from the lens will become larger, while the part of the groundglass that moves closer to the lens will become smaller.
Tilting the front of the camera affects the focus because the focal plane of the lens moves. Swinging the front of the camera swivels the lens to the left or right and, as a result, skews the focal plane of the lens to one side or the other. The general effect is to create a sharply defined zone of focus that travels at an angle across an object.
Slide, rise, and fall move the entire front or back of the camera on a flat plane. Slide moves the front or back to the left or right; rise moves the front straight upward; fall moves the front straight downward. These movements will allow the angle between the planes of film, lens, and subject to remain the same but will change the placement of the image on the film.
A slide of either the back or front of the camera produces similar results - image shape does not change with a back slide, but it changes slightly with a front slide. Rise or fall of the front causes a change in the point of view (or the space relationship) between any objects in the frame as well as a slight change in shape.

Film Loading

After you've made the final adjustments to your image composition, you're ready to load film into the camera. As mentioned earlier, Media Loan can provide two types of film holders for the Calumet 4x5: a 4x5 sheet film holder and a 4x5 Polaroid pack film holder.
Before loading film into the sheet film holder, the holder must be cleaned. Remove the slides and open the flaps at the bottom of the holder. Brush out the entire interior of the holder on both sides. (A small bristle paintbrush works well.) Use a soft cotton cloth to wipe the slides clean.

SHEET FILM LOADING

The film sheets must be loaded into the holder in complete darkness. Load the sheets with the emulsion side facing out. For positive identification of the emulsion side of the film while working in the dark, there are a series of notches in the corner of the sheet, When the film is held in the right hand with the thumb and index finger at the lower right hand corner, if the index finger is resting on the notches, the emulsion side is facing up.
Use the left thumb and forefinger to help guide the edge of the film and push completely into place. Slip a fingernail under the end to try and lift it up. If it lifts up, the film hasn't actually slid into the grooves.
Finally, close the flap at the bottom of the holder and insert the dark slide with the lighter edge (silver or white) out - indicating the film is unexposed. The light colored side has a series of notches which will facilitate the process in the dark. After exposing the film, this slide will be reinserted with the dark side out to indicate the film has been exposed. Two sheets of film may be inserted into one holder, one on each side. Save your empty film boxes and packaging for storing your exposed film. Be sure to clearly mark "exposed" on the appropriate package to eliminate confusion later. To load the filled holder into the camera, first make sure all adjustment knobs have been tightened down so the loading procedure won't disturb your composition. Then pull out on the frame release handle on the back of the camera until it extends at a right angle and the small rollers rest in the depressions. Insert the film holder in the space behind the groundglass, making sure the bottom of the holder rests on the protruding stops. Release the frame release handle to close up the camera back.

POLAROID FILM LOADING

To load film into the Polaroid holder follow the instructions on the holder and film sheets. Loading the Polaroid film packs doesn't need to be done in darkness, as the packaging protects the photosensitive surface.
The Polaroid holder must be clean to operate properly, but doesn't need cleaning with each use as do the film sheet film holders. Check the rollers for an accumulation of chemical residue and follow the cleaning instructions on the holder.
Before inserting the Polaroid film packets, check to make sure the operating lever moves the catch at the end of the holder which must grab the metal strip on the end of the film packet. Also, when removing the center of the film packet to expose the film, don't remove it all the way as it will then be impossible to reinsert. Finally, when you're ready to process the Polariod sheet, make sure the operating lever is pushed all the way to the P and not caught on an adjacent lever.

Exposing the Film

After you've taken a light meter reading, you must also compute how much to increase the exposure based on the length of the bellows. This is called adjusting for the bellows factor and is computed using the following formula:
Bellows Length
------------------------ = Exposure Increase
Focal Length
The lens focal length is noted on the lens itself. (Media Loan's Calumet lenses have a six inch focal length.) Obtain the bellow length by measuring with a ruler from the lens to the film plane.
Close the camera shutter and then adjust its speed for the appropriate exposure based on the preselected diaphragm setting. Cock the shutter and remove the dark slide from the film holder. Now you must wait until any vibrations of the camera resulting from these procedures have had a chance to subside. Finally, use a cable release to open the shutter; pressing the shutter release button by hand could generate enough movement to dull the image sharpness.
After exposing your film, replace the dark slide with the dark edge out and turn the latches on the end of the holder to make certain the slide won't be accidentally pulled out.



Landscape Photographers

John Schott
Ansel Adams
Hamish Fulton
Richard Long
Edward Weston
Ed Ruscha
Lewis Baltz
John Davies
Nicholas Nixon
Eugene Atget
Alfred Stieglitz
Frank Gohlke
Henry Wessel
Robert Adams
Axel Hutte
Bernd & Hilla Becher
Stephen Shore
Andreas Gursky
Edward Butynsky

Hamish Fulton


Hamish Fulton British artist and photographer was born in 1946 in London England. He first attended the art foundation course at Hammersmith college of Art.

Richard Long


Richard Long is an English sculptor photographer and painter one of the best known British landscape artists. Long is the only artist to be shortlisted for the Turner Prize.

Edward Weston


Edward Henry Weston was a 20th century American Photographer. He has been called one of the most innovative and influential American photographers and one of the masters of the 20th century photography.

Ansel Adams


Ansel Adams was an American photographer and environmentalist. His black and white landscape photographs of the American west especially Yosemite National Park have been widely reproduced on calenders posters and in books.